Dongguan Tom Mason Teflon wire extrusion machine, Teflon extrusion machine, extrusion machine Dongguan Teflon wire, Teflon extrusion machine price, Teflon Extrusion Machine Supplier: Dongguan City, Tom Mason Wire & Cable Co., Ltd. 

 Teflon extrusion machine uses and technical characteristics 
 Teflon wire extrusion machine extrusion machine, also known as Teflon, used for high-temperature fluorine plastic wire, tube and extrusion and multilayer thin insulation extrusion, local cable wire extrusion, extrusion, etc. outside. 
 1. Adapted to the FEP (perfluorinated ethylene propylene polymer, also known as F46), FPA (alkoxy vinyl oxide) and ETFE (also known as F40) and other fluorine plastic production. 
 2. Screw Barrel: steel 3 are new GH113 (GDA material with the United States) or the use of imported high-temperature corrosion-resistant Hastelloy magic. 
 3. Head: 3 new exclusive free magic GH113 material transfer head or adjustable nose or use nose Swiss import Microdia, vacuum devices. 
 4. Heating system: The temperature of the copper alloy heaters. 
 5. Quality control: the feedback device with a diameter of detection, Japan TAKIKAWA detector bump diameter control products throughout the United Kingdom BETA water capacitor tester, high-frequency spark machine and process parameters such as concentricity. 
 6. Electronic control: import converter (Siemens motors, Emerson Drive, etc.). 

 Teflon (fluorine plastic) out of the situation analysis of the actual production 
 With fluorine plastic casing extrusion mold, mold design or mold used in production must ensure that DDR (draw ratio), DBR (the draw ratio balance) values ??of two parameters in the extrusion material to the extent permitted within. Just started production FEP material, the use of the material is DuPont's 5100 # 6100 # 5010 # 5030 # 5010 # and 5030 # which is the production of foam wire. Agents in Shanghai, according to DuPont introduced the characteristics of the material learned: 
 Open wire wire: DDR in the range between 80 to 140; DBR in the range between 0.9 to 1.1. 
 Follow-up in the open all kinds of wire, have adopted these kinds of wire DDR, DBR's range, generally take the median value, in order to calculate the inside out mold and mold. 
 Example: Prior to the test machine came open outside the FEP wire, the material is FEP5100 # required OD: 0.86 ± 0.01, conductor: 0.508. The use of mold: 9.2 in 1.04 × 5.59 outside, as DDR and DBR can be calculated 
 Derived from the above value of DDR and DBR can be seen, there is a large range of its available, if the same outer mold aperture, while the DDR values ??were 80 and 140, it is calculated as follows: assumptions about the model diameter (unknown) for the X2, DDR value of 80, in order to calculate the X = 67.4. The DBR is clearly greater than 1.1, can not be produced within the wire will break into shares of other adverse conditions 

 Teflon extrusion machine technical parameters: 
 TMS-25 ~ 30 TMS-35 TMS-45 TMS-50 TMS-65 
 Active form of Actinobacillus Actinobacillus Actinobacillus active active / uniaxial tension, biaxial tension Actinobacillus Actinobacillus 
 Extrusion speed 180,180,180,150,150 
 Screw 26:1 25:1 25:1 25:1 25:1 
 Screw speed 10-90 10-90 10-90 10-9010-70 
 Extrusion Output 20,254,560,100 
 Applicable wire Φ0.2-φ2.0 Φ0.4-φ3.0 Φ0.6-φ8.0 Φ0.6-φ8.0 Φ1.0-φ10.0 
 Host power 11KW 11KW 15KW 15KW 22KW 
 Take-Power 2.2KW 2.2KW 2.2KW 2.2KW 4.0KW 
 Take-Power 1.5KW 1.5KW 1.5KW 1.5KW 2.2KW 
 Take-up devices dual-axis loading bar / shaft-mounted 
 Dual control electric control + PLC + HMI full control (optional) 

 Fluorine plastic extruder die on the application 
 This is the way to increase the brightness of the new method of product, PTFE is a fear of fire in high-temperature insulation material, because of its high temperature and the formation of its high density it can not be replaced by other substances, the role of specific applications as follows : 
 1. Expansion of the mold jacket diameter 8 - 10MM and leaving a block at the outer edge of its units to the impedance extruder pressure, Taiwan's large diameter than the original diameter of 5MM or so. 
 2. Fluorine end of the cylinder filled car into the outer mold machined inner diameter, the diameter of the stage and then car (Note that stage than the big 1 - 1,5 MM because of expansion and contraction fluorine plastic) into the fluoroplastic has processed mold. 
 3. Note that processing must be smooth and good mold wall, can not use that fire, mold in the event of scratches when the change in time, the most important thing has been out of the material is very light material can cover up their own temperature, there is some experience before operational. Fluorine plastic will shrink the first time, do not let him die gap and the outer feed. Be sure to choose good quality Teflon, this mold is only applicable to PVC material. 

 Keywords: Teflon Extruder Extruder price Dongguan Teflon electromechanical cable extrusion line extrusion machine